Redwood privacy fencing, ornamental iron, pool enclosures, and Zone Zero non-combustible systems — built for Peninsula lots, permitted correctly, built to last.
Every material, every configuration, permitted in every city we serve.
Con-Heart redwood built for the Peninsula’s coastal climate — board-on-board, dog-ear, and custom heights. All hardware hot-dipped galvanized. Every post set right.
We build with Con-Heart redwood: clear of knots, consistent in grain, and selected for structural integrity from post to cap. Whether you are replacing a weathered old fence or starting fresh on a new lot, Con-Heart grade is dimensionally stable in coastal humidity, naturally resistant to the conditions that degrade other wood species, and takes finish well.
Post installation is where most fences fail early. We dig to the correct depth for your soil conditions, set posts with proper drainage at grade, and treat all cut ends before they go in the ground. On rocky or unstable Peninsula soils we use steel post systems that anchor without a full concrete pour. All hardware is hot-dipped galvanized or stainless.
Board-on-Board is the most popular layout on the Peninsula — alternating boards on both sides of the stringer create full privacy from every angle while allowing airflow. Dog-Ear single-face is a clean traditional look that works well on flat lots. Both can be built at standard 6-foot height or taller where code allows.
Custom entry gates, driveway gates, ornamental railings, and security fencing — fabricated and finished for coastal salt air exposure. Automation coordination available.
Iron work on the Peninsula has one enemy above everything else — salt air. We spec and finish every iron gate and railing for coastal exposure: proper primer, powder coat or high-solids enamel, and hardware that won’t seize up after two winters of marine layer. A gate that looks great on installation day but starts rusting at the welds two years later is a finish system failure.
Custom entry gates are one of the most impactful improvements you can make to a Peninsula property. We fabricate single and double swing gates, slide gates for driveway applications, and pedestrian walk gates in a range of profiles from simple flat-bar to ornamental spear-top. Hardware is specified for the gate weight and use frequency. Where automation is wanted, we coordinate with gate operator suppliers for a clean, integrated installation.
Iron deck and stair railings pair naturally with our redwood deck and stair work. For properties in fire hazard zones, iron and steel fencing also qualifies as a Zone Zero non-combustible solution at the property line.
California code-compliant pool enclosures — self-closing, self-latching, built to pass inspection on the first visit. Aluminum, glass, and wood systems available.
California Health and Safety Code Section 115922 requires a compliant barrier around any residential pool or spa. The code establishes minimum fence height (48 inches measured from outside), maximum opening sizes (no sphere larger than 4 inches can pass through), self-closing and self-latching gate requirements, and specific rules for latch placement. Several Peninsula cities have adopted local amendments stricter than state minimums — we build to those requirements when they apply.
The hardware is where pool fencing most often fails in practice. A gate that is self-closing on installation day but drifts out of adjustment within a year — because the hinges were not specified for the gate weight — is a compliance and safety failure. We specify hardware rated for the actual gate weight and use frequency, and set posts to the correct depth in concrete.
Glass panel systems provide a clean, unobstructed view of the pool area while meeting every code requirement. Powder-coated aluminum is the most common choice: durable, corrosion-resistant, and available in a range of profiles and colors. Every system uses pool-environment rated hardware throughout.
Steel, aluminum, and masonry fencing for WUI and fire hazard severity zone properties. Zone Zero compliant at the house connection — material certification included in every permit package.
California Assembly Bill 3074 directed the State Board of Forestry and Fire Protection to establish a Zone Zero — covering the first five feet around every structure. CAL FIRE’s research is unambiguous: most homes lost in California wildfires ignite from wind-blown embers that accumulate in this zone. A wood fence connected to the house here acts as a direct fuel path. On the Peninsula, hillside communities in Pacifica, Brisbane, San Bruno, Millbrae, and unincorporated San Mateo County sit within CAL FIRE-designated Very High Fire Hazard Severity Zones.
For most existing Peninsula wood fences, a full replacement is not required. The common approach is a non-combustible transition at the house connection — an iron or steel gate and panel in the Zone Zero area, with wood fencing continuing beyond it. This targeted approach addresses the ember pathway without requiring a full fence replacement.
Non-combustible does not mean industrial or plain. Powder-coated aluminum and steel systems are available in a range of profiles that complement both contemporary and traditional Peninsula architecture.
Every material has a place — the right choice depends on your property, your city’s codes, and what you are trying to accomplish.
Redwood is native to Northern California — dimensionally stable in coastal humidity, naturally resistant to the conditions that degrade other wood species, and takes finish well. Con-Heart grade (clear of knots, cut from the heartwood) is what we specify for structural fence applications. It machines cleanly, holds fasteners well, and presents a consistent face from board to board.
Board-on-Board is the most popular layout on the Peninsula — alternating boards on both sides of the stringer create full privacy from every angle while allowing airflow. Dog-Ear single-face is a clean traditional look for flat lots. Both can be built at standard 6-foot height or taller where code allows.
Posts are concrete-set at appropriate depth for your soil and fence height. On rocky or unstable Peninsula soils we use steel post systems that anchor without a full concrete pour. All hardware is hot-dipped galvanized or stainless — standard hardware corrodes fast in coastal air and we do not use it.
Redwood can be left to weather naturally to a silver-gray patina, sealed clear to preserve the warm tone, or finished with a penetrating stain. A properly built redwood fence handles Peninsula conditions with minimal maintenance when finished correctly from the start.
A privacy fence is defined by function — full visual screening from ground to top rail — not by a single material. We build privacy fences in redwood, composite board systems, and vinyl depending on the property. The layout — Board-on-Board, solid-face, or shadowbox — determines the privacy level and how the fence responds to coastal wind.
Most Peninsula cities allow 6-foot privacy fencing in rear and side yards without a permit. Front yard heights are regulated — typically 3 to 4 feet. Corner lots have additional sight-line rules. We pull every permit required and handle all coordination with your city’s building department.
Redwood is the traditional choice and the one we build most often. Composite board systems are a strong alternative where low maintenance is the priority. Vinyl is available but we specify it selectively — it can be problematic on exposed hillside lots with significant wind loading.
Every privacy fence we build can be paired with walk gates, double drive gates, or combination setups — frames built from the same material as the fence, reinforced at the corners, hung on heavy-duty hardware rated for the gate weight.
California Health and Safety Code Section 115922 mandates a compliant barrier around every residential pool and spa. The code requires a minimum 48-inch fence height, maximum 4-inch sphere opening, and self-closing, self-latching gates that open away from the pool. Several Peninsula cities have adopted stricter local amendments — we identify those at the estimate.
Pool fencing is most commonly built in powder-coated aluminum (corrosion-resistant in pool chemical environments) or glass panel systems for an unobstructed view. We also build code-compliant wood pool fences where site conditions support it. Every system uses pool-environment rated hardware throughout.
The gate is the most critical safety element of a pool enclosure. It must be self-closing from any open position, self-latching, and open away from the pool. We specify hinge and closer hardware rated for the actual gate weight — an undersized closer that drifts out of adjustment is a safety failure.
A pool fence permit is required in every Peninsula city. The inspection is more thorough than a standard fence permit. We handle the application, coordinate with the building department, and schedule the inspection. Our enclosures are built to pass on the first visit.
A significant portion of the Peninsula — particularly Pacifica, San Bruno, Millbrae, and unincorporated San Mateo County — sits within CAL FIRE Very High Fire Hazard Severity Zones. Fencing is included in the material restrictions. Iron and steel fencing qualifies as non-combustible and is one of the most straightforward ways to meet Zone Zero requirements.
Non-combustible fencing systems include aluminum, steel, masonry, and specific composite products tested and listed by the California State Fire Marshal. Not all composite products qualify — the material must carry the appropriate rating. We maintain current SFM listings for the products we install.
Non-combustible does not mean industrial or plain. Powder-coated aluminum and steel systems are available in a range of profiles and colors that work with both contemporary and traditional Peninsula architecture. We will show you what has been installed on comparable properties in your area.
Fire-zone fence permits require material documentation. We maintain product specs and California State Fire Marshal listings for everything we install and include that documentation in every permit package. If you are unsure whether your property is in a fire hazard zone, we confirm that at the estimate.
The questions we hear most — before the estimate, during the build, and after.
We install redwood and cedar privacy fences, pool safety fences, ornamental iron and steel fences, automatic and manual gates, and non-combustible fencing for WUI and Zone 0 fire hazard zones. We select materials based on your site, HOA rules, and local requirements.
It depends on height, location, and your city. Most Peninsula cities allow fences up to 6 feet in rear and side yards without a permit, but front yard fences and fences near property lines often have stricter rules. We confirm what applies to your specific address at the estimate.
A properly installed redwood or cedar fence typically lasts 15 to 20 years with basic maintenance — occasional cleaning and a coat of sealer every few years. Heart redwood is naturally rot-resistant. Posts set in concrete with proper drainage are the single biggest factor in fence longevity.
Yes. We do partial replacements, post replacements, and section repairs regularly. We’ll assess the existing fence and let you know whether a repair or a full replacement is the better long-term value for your situation.
Zone 0 refers to the immediate 0–5 foot zone around a structure in a Wildland-Urban Interface (WUI) area. California fire code increasingly requires non-combustible materials in this zone. We install qualifying metal, concrete, and masonry fence systems for properties in Pacifica, Brisbane, and other hillside Peninsula cities subject to these regulations.
Yes. We install slide gates, swing gates, and driveway entry systems with electric operators. We handle the ironwork, the motor installation, and the wiring rough-in. For low-voltage and smart-home integration we coordinate with your electrician or can recommend one.
This varies by city and zoning. In most cases a fence can be built directly on the property line, but setback rules and neighbor consent requirements differ. We help you understand what’s allowed before the project starts so there are no disputes after.
Free estimates on all fencing, decking, hardscape, and custom projects across the Peninsula.
